Electronics Line 3208GLD Uživatelský manuál stáhnout pdf (Strana 30)

ADDRESSES 180 - 195: ACCOUNT NUMBERS

Account numbers are transmitted to the central station with the event code to identify the source of the

event. Each system can be given a separate account number. If the system is not partitioned, only enter

the account number for System 1. For partitioned systems, program account numbers for all sub-

systems. Account numbers are entered in four consecutive addresses. To enter an account number

always enter 8 digits in sequence (if the number is less than 8 digits, use leading zeros).

Certain protocols can handle more than one transmission length. This means that in some protocols

either 5 or 8 digit account numbers, for example, can be sent. The following example illustrates how to

program account numbers for a protocol that handles 3 or 4 digit account numbers.

When transmitting an account number to the central station, the control panel automatically ignores any

sequence of zeros at the beginning of the number.

Enter the following to program a 3 digit account number for System 1:

Address →

180 181 182 183

Value →

00 00 01 23

In the above example the account number will be regarded as “123”. If a 4 digit account number “0123” is

required, enter the following:

Address →

180 181 182 183

Value →

10 00 01 23

The first digit indicates to the control panel that the zero is to be considered as part of the 4 digit account

number.

180-183 Account # for System 1

184-187 Account # for System 2

188-191 Account # for System 3

192-195 Account # for System 4

ADDRESSES 196-197: TELEPHONE LINE PARAMETERS

196 First Digit: Dialing Options and Telephone Event Message Enable/Disable

The first digit of this address comprises the following options.

• Dialing Initiation – the control panel only dials if a dial tone is detected within the time-out

(programmed at address 197) or allowed anyway after the second time-out.

• Dialing Mode – the panel can be programmed to use either pulse or tone (DTMF) dialing.

• Telephone Event Message Enable/Disable – this option enables or disables telephone

communications to the central station and follow-me number. If disabled, there is no need

to program any of the other parameters regarding central station communications

(telephone numbers, event codes etc.).

Note: This option does not affect RP communications. The RP Callback number,

addresses 172-179, may still be programmed.

First digit value:

Dialing Initiation Dialing Mode Telephone Event Message Value

Pulse No 0

Dial Anyway Yes 2

DTMF No 4

Yes 6

Pulse No 8

Do not Dial Yes A

Without Tone DTMF No C

Yes E

Second Digit: Time-Outs for Acknowledgment

Acknowledgments are tones transmitted from the central station to the control panel to confirm

successful transmission of event codes. There are 2 acknowledgment tones, Ack1 and Ack2.

Ack1 is the tone that confirms that the central station has recognized that the panel is

attempting to send an event code. Time-Out for Ack1 is the amount of time the panel waits for

Ack1 to be sent after the central station picks up. If Ack1 is not received within this time period,

the panel makes another dialing attempt (if programmed at address 197). Ack2 is the tone that

confirms that the central station has received and understood the message. Time-Out for Ack2

is the amount of time the panel waits for Ack2 after sending the message. If Ack2 is not

received during this time period, the panel makes another message attempt (if programmed at

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 50 51

Komentáře k této Příručce

Žádné komentáře

Electronics Line 3208GLD Uživatelský manuál Strana 30

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Electronics Line 3208GLD