Electronics Line 3208GLD Uživatelský manuál stáhnout pdf (Strana 6)

System Partitioning

The system can be partitioned into a maximum of 4 independent sub-systems with individual account

numbers, keypads, user codes and relays assigned exclusively for each sub-system. A sub-system is

created when at least one zone is assigned to it.

1.3: Telephone Dialer

The Summit 3208GLD allows for up to four different telephone numbers to be programmed into the system

using either pulse or tone dialing. The Summit 3208GLD supports several communication protocols

including pulse protocols enabling communication with most popular central station receivers. Up to 16

digits can be programmed for each telephone number. Different groups of event messages (Burglary, Fire,

Open/Close messages etc.) can be programmed for single or multiple central station notification, enabling

notification of up to four central stations. Message transmission can be programmed as Primary, Backup or

Duplicate.

In some cases the central station handles events reported per zone and in others per event. Additionally, an

event code can comprise of either one or two digits and can include additional information such as the user

number in opening and closing messages or zone ID in event oriented zone messages. These codes are

usually assigned by the central station - consult the central station operator for a listing of the different event

codes.

Follow-me

Using the Follow-me feature, the panel can notify the user that the system has undergone certain events by

sounding a sequence of tones over the telephone. The user acknowledges that the message has been

received by pressing 0, 9 or # on their telephone. If this acknowledgement is not received within the one-

minute time window, opened the moment the panel starts dialing, the control panel redials. The number of

dialing attempts made depends on the value programmed at address 197.

Telephone #4 is designed for use with this feature, as it is the only telephone number that can be easily

programmed by the user, without the need to enter programming mode.

Telephone Line Supervision

Approximately 20 seconds after the telephone line is cut, all keypads sound a trouble beep and the

message “Telephone Comm. Failure” appears on LCD keypads.

1.4: Remote Programming

Electronics Line’s remote programming software enables all programming and operation to be performed

from a PC. This can be done from either a remote location or on-site using the ‘Off-hook’ communication

option. The software provides a comprehensive interface to the Summit 3208GLD control panel facilitating

and cutting down the time taken in programming the system.

A number of programmable options, relating to when and how RP communication is established, are

available at address 496. The tollsaver feature, RP Callback, makes remote programming more cost-

effective and increases the level of security. Using this feature, the Remote Programmer establishes a

connection with the panel. The panel recognizes the passcode, hangs up and calls the number programmed

at addresses 172-179 within 60 seconds.

Answering Machine Override

Answering machine override enables the control panel to distinguish between regular incoming calls and a

communication attempt by the RP (remote programmer) software. An RP call is identified by the control

panel as a sequence of two calls within a 30-second time window.

1. The control panel does not answer the first incoming call.

2. The control panel opens a 30-second time window from the moment the telephone stops ringing.

3. The control panel answers after 1 ring and RP communication is established.

Note: The 30-second time window will only start if the number of rings in first call exceeds the

number of rings set for the control panel. For example, if the control panel is programmed to pick

up after 3 rings, the time window will not start unless the first call was at least 3 rings.

1 2 3 4 5 6 7 8 9 10 11 ... 50 51

Komentáře k této Příručce

Žádné komentáře

Electronics Line 3208GLD Uživatelský manuál Strana 6

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Electronics Line 3208GLD